NACE CIP Level 1 Study Questions with Correct Answers

NACE CIP Level 1 Study Questions with Correct Answers

NACE CIP Level 1 Study Questions
with Correct Answers

1. You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank
   lining is being applied. After the application of the 19 coat, you notice small blisters in
   some areas of the applied lining.
   Your FIRST preferred course of action is to:
   A. Break the blisters to see what’s inside
   B. Document the problem and advise the Contractor and Owner’s representative
   C. Document the problem and advise the Contractor
   D. Extract any liquid that may be inside the blister and send it to the lab for further
   analysis
   Correct Answer:
   B. Document the problem and advise the Contractor and Owner’s representative
2. Dew point is the temperature at which
   A. water freezes.
   B. humidity decreases
   C. condensation occurs.
   D. the air is saturated.
   Correct Answer:
   C. condensation occurs.
3. If a contractor is using a poorly maintained compressor to supply air for abrasive blast
   cleaning and conventional air-spray, the coating inspector should perform a
   A. dry film thickness (DEI) measurement.
   B. wet film thickness (WFT) measurement.
   C. blotter test for the presence of oil and water.

D. vial lest.
Correct Answer:
C. blotter test for the presence of oil and water.

4. Upon arrival of coating materials, the inspector should
   A. review coating contractors’ plans for storage of coating materials and confirm they
   meet national, local and owners’ fire and environmental regulations.
   B. observe and document the amount of material and batch numbers. C. observe aryl
   document that the applicator WFT at regular intervals during application.
   D. observe and document time frame and environmental conditions between each coat.
   Correct Answer:
   B. observe and document the amount of material and batch numbers.
5. Relative humidity is
   A. a measure of the amount of moisture in the air compared to saturation level.
   B. a measure of the amount of moisture in the air compared to the air temperature.
   C. the lowest temperature at which moisture forms on a steel surface. D. the highest
   temperature at which moisture forms on a steel surface.
   Correct Answer:
   A. a measure of the amount of moisture in the air compared to saturation level.
6. Galvanic corrosion occurs on which of the following substrates:
   A. Concrete
   B. Fiberglass Reinforced Plastic
   C. Metal
   D. Wood
   Correct Answer:
   C. Metal
7. When applying Thermal Spray Coatings the specification is most likely to reference:
   A. SSPC PA 2
   B. NACE SP 0178
   C. NACE SP 0188

D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
Correct Answer:
D. SSPC-CS 23.00/AWS C2.23/NACE No. 12

8. What is the minimum recommended distance away from an edge that an inspector
   should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT)
   gauge?
   A. 1 cm (.39 inch)
   B. 2.5 cm (1 inch)
   C. 6.35 cm (2.5 inch)
   D. 2.5 millimeters (.10 inch)
   Correct Answer:
   B. 2.5 cm (1 inch)
9. Polymerization is the process of:
   A. Monomers telegraphing
   B. Monomers joining together
   C. All thermoplastic coatings
   D. All organic coatings
   Correct Answer:
   B. Monomers joining together
10. An exposed area of the substrate or previous coat of a conductive coating material,
    often caused by poor application technique is called
    A. cracking.
    B. sagging.
    C. holiday.
    D. checking.
    Correct Answer:
    C. holiday.
11. Checking is
    Powered by https://learnexams.com/search/study?query=