Shovels typically have handles made of wood or

Shovels typically have handles made of wood or . Fiberglass Before using a pick, make sure that the head is . Fixed firmly to handle A chain fall locks its elevated load in place using . Automatic brake Cable come-alongs are used to move loads . horizontally for short ground distances Because of the shape of its jaws, a , clamp can spread clamping pressure over a wider area than other clamps. hand screw The best designed saw for cutting miter joints is a . backsaw When using a utility knife, place a piece of scrap material under the object you are cutting in order to _. protect the surface under the material The safest kind of utility knife is one with a . Self retracting blade To check level conditions over a significant distance, such as building foundations or longer distances, the best level to use is a laser level A has fewest teeth per inch resulting in largest teeth. rip saw Another common name for lineman pliers is . side cutters Because of its stiffness, a folding rule is better than a cloth or steel tape for measuring . vertical distances One situation that can make a measurement with a laser inaccurate is measuring to a . highly reflective surface When an object is plumb it is . perfectly vertical In addition to level and plumb, some spirit levels can check a . 45 degree angle To quickly run a nut on to a bolt that resists spinning it on with the finger, you can drive the socket with a . speed handle A spud wrench is different from a pipe wrench in that . it has smooth jaws How many sides does a hexagonal shape have? 6 is the type of screw that comes to a relatively sharp point at the base of its drive socket. Reed and Prince The proper angle for the edge of a cold chisel is . 60 degrees A heavy-duty tool used to drive posts or other large stakes is a . sledge hammer Another name for a machinist hammer is ___. ball peen

The Correct Answer and Explanation is :

1. Shovels typically have handles made of wood or fiberglass.

• Fiberglass is a durable material that is often used as an alternative to wood for shovel handles. It’s lightweight, resistant to breakage, and can withstand harsh weather conditions. Fiberglass also has a higher tensile strength than wood and doesn’t splinter.

1. Before using a pick, make sure that the head is fixed firmly to the handle.

• The head of the pick should be tightly secured to the handle to ensure safety during use. If it is loose, the head can detach while swinging, causing injury or damage. A pick’s head is usually affixed with a wedge or a metal pin.

1. A chain fall locks its elevated load in place using an automatic brake.

• A chain fall, or chain hoist, uses an automatic brake to secure the load when it is lifted. The brake prevents the load from falling and provides safety during the lifting process. It’s commonly used in construction and heavy-duty applications.

1. Cable come-alongs are used to move loads horizontally for short ground distances.

• Cable come-alongs, or cable winches, are manual tools used to pull or tension heavy loads over short distances. They are often used in construction and in situations where a mechanical winch is impractical.

1. Because of the shape of its jaws, a hand screw clamp can spread clamping pressure over a wider area than other clamps.

• Hand screw clamps have adjustable, wooden arms with wide jaws that provide uniform pressure across the clamped area. This makes them ideal for delicate or uneven surfaces where other clamps might damage the material.

1. The best designed saw for cutting miter joints is a backsaw.

• A backsaw has a rigid back edge to keep the blade straight, making it perfect for precision cutting, such as miter joints. It provides controlled, clean cuts necessary for the perfect fit in frame construction.

1. When using a utility knife, place a piece of scrap material under the object you are cutting in order to protect the surface under the material.

• Using a scrap piece underneath protects the surface you are cutting on from accidental damage, which could happen when the blade goes through the material.

1. The safest kind of utility knife is one with a self-retracting blade.

• A self-retracting blade automatically pulls back into the handle when not in use, preventing accidental cuts and making it safer compared to fixed-blade utility knives.

1. To check level conditions over a significant distance, such as building foundations or longer distances, the best level to use is a laser level.

• Laser levels project a precise, visible laser line across a distance, making them ideal for checking horizontal or vertical alignment over long distances. They are more accurate and efficient than traditional spirit levels.

1. Arip sawhas fewest teeth per inch resulting in the largest teeth.
   • A rip saw is designed for cutting along the grain of the wood. It typically has fewer teeth, which makes the cuts rougher but faster, as fewer teeth can engage with the wood.
2. Another common name for lineman pliers isside cutters.
   • Lineman pliers, or side cutters, are used for gripping, twisting, and cutting wire. The term “side cutters” refers to the flat cutting edges on the side of the jaws.
3. Because of its stiffness, a folding rule is better than a cloth or steel tape for measuringvertical distances.
   • A folding rule, being rigid and non-flexible, is ideal for vertical measurements where precision is key. Unlike a tape, which can bend or sag, a folding rule holds its shape and ensures accurate readings.
4. One situation that can make a measurement with a laser inaccurate is measuring to ahighly reflective surface.
   • Laser measurements can bounce off highly reflective surfaces, such as mirrors or windows, resulting in incorrect readings.
5. When an object is plumb it isperfectly vertical.
   • Plumb refers to something that is perfectly vertical, in contrast to level, which refers to something being horizontally aligned.
6. In addition to level and plumb, some spirit levels can check a45-degree angle.
   • Some spirit levels are designed with vials for checking 45-degree angles, allowing for more versatile use in construction and carpentry.
7. To quickly run a nut on to a bolt that resists spinning it on with the finger, you can drive the socket with aspeed handle.
   • A speed handle is a tool used to quickly tighten or loosen nuts and bolts. Its handle allows for rapid, continuous motion to turn a socket without needing to reposition the wrench.
8. A spud wrench is different from a pipe wrench in thatit has smooth jaws.
   • A spud wrench is used for aligning and adjusting bolts in construction and piping. Unlike a pipe wrench, which has serrated jaws for gripping pipes, a spud wrench has smooth jaws that don’t damage or deform the material.
9. How many sides does a hexagonal shape have?6
   • A hexagon has six sides, and it is commonly seen in architecture, design, and various mechanical applications.
10. __ is the type of screw that comes to a relatively sharp point at the base of its drive socket.Reed and Prince
    • Reed and Prince screws have a sharp point at the base of their drive socket that helps prevent slippage and allows for a more secure grip when using a screwdriver.
11. The proper angle for the edge of a cold chisel is60 degrees.
    • A 60-degree angle is ideal for cold chisels, providing the proper balance between strength and sharpness to cut through metal without dulling the edge quickly.
12. A heavy-duty tool used to drive posts or other large stakes is asledge hammer.
    • A sledgehammer is a large, heavy tool used for driving posts, breaking objects, or tasks that require significant force.
13. Another name for a machinist hammer isball peen.
    • A ball peen hammer is used in metalworking. Its round head (ball peen) is used for shaping and rounding metal edges.

Each of these tools has specialized uses that increase their effectiveness and safety in various construction, mechanical, or precision tasks.