3CX ADVANCED CERTIFICATION EXAM 2023-2024 ACTUAL
EXAM 100 QUESTIONS AND CORRECT DETAILED
ANSWERS|AGRADE||NEWEST UPDATE
Your 3CX has only one SIP Trunk and receives a call from number
- If you have a “Inbound CID Reformatting” rule on the
Trunk with “Source Pattern” 813(…)(.) and “Replace Pattern” \1\2, the extension that receives the call will see “5791691” as the caller ID on its display. – ANSWER- True When 3CX has been installed without a FQDN from 3CX and in split DNS mode, the DNS server must not be installed on the same machine as the phone system. – ANSWER- True Your Local IP Phone loses the registration to 3CX and you want do troubleshoot the issue. You should start a Wireshark Capture on the 3CX Server, reboot the phone, and then apply the Filter sip.Cseq.Method==REGISTER in order to see if registrations are reaching 3CX – ANSWER- True Your 3CX has only one SIP Trunk and receives a call from number 422033272020 and you want it to be presented on the extension display as +44272020. You can do this with a “Inbound CID Reformatting” rule on the Trunk with “Source Pattern” 44(..)(..)(.) and “Replace Pattern”
+44\3. – ANSWER- True
When selecting the option “I need a 3CX FQDN” an internal DNS is not
mandatory – ANSWER- True
The order of “Inbound Rules” is not important when you have DID and
CID “Inbound Rules”, CIDs always have higher priority. – ANSWERFalse
You have a Master Bridge with 3-digit extensions 1xxx and a Slave
Bridge with 4-digit extensions 2xxx. In the “Outbound Rules” you use to
rote calls across the bridge, using a prefix is mandatory. – ANSWERFalse
You have run the 3CX “Firewall Checker” and comes up as Green, but
you still have audio issues and calls dropping on on outbound / inbound
calls. Can SIP ALG be the culprit? – ANSWER- True
An extension will be allowed up to 25 attempts (default) for
authenticating successfully, after what it will be blacklisted for the
default blacklisting interval of 1800 minutes. – ANSWER- False
The 3CX SIP port should be filtered by firewall ACL rules to maximize
security and allow only trusted IPs to reach it (VoIP providers or STUN
extensions if any). – ANSWER- True
SRTP will secure calls so that a middle-man can’t see the SIP traffic in
plain-text. – ANSWER- False
3CX BASIC CERTIFICATION EXAM 2023-2024 ACTUAL
EXAM 100 QUESTIONS AND CORRECT DETAILED
ANSWERS|AGRADE||NEWEST UPDATE
3CX requires a … in order to be setup – ANSWER- FQDN
NAT translates … IPv4 IP addresses to … private IP adresses –
ANSWER- Public, private
NAT can also be used to limited who can access the server using? –
ANSWER- ACL
IPv4 and … are supported by 3CX – ANSWER- IPv6
IPv6 … (NAT) is not supported by 3CX – ANSWER- Masquerading
If IPv6 is used … rules are needed – ANSWER- Firewall
3CX PBX requires … NAT – ANSWER- Full Cone
SIP/SDP defines the port not the … – ANSWER- Transport header
It is recommended to … SIP ALG – ANSWER- Disable
The default SIP ports are … UDP/TCP – ANSWER- 5060
What NAT port range does 3CX use for audio? – ANSWER- 9000 –
10999 UDP
If you want to use the 3CX app or use an SBC you will need to open the
PBX tunnel port. The default TCP/UDP port is? – ANSWER- 5090
If you want to use the 3CX app or use an SBC you will need to open the
HTTPS port. The default TCP port is? – ANSWER- 5001
To enable the use of 3CX webmeeting you will need to allow outbound
traffic to … – ANSWER- webmeeting.3cx.net:443
3CX Webmeeting requires that the HTTPS Port is open for TCP traffic,
which port is this? – ANSWER- 5001
Port … TCP is used to provision IP phones – ANSWER- 5001
To perform remote configuration of the PBX you will need to allow
inbound traffic on port … TCP for the duration of the setup. – ANSWER5015