{"id":112927,"date":"2023-08-15T21:25:53","date_gmt":"2023-08-15T21:25:53","guid":{"rendered":"https:\/\/learnexams.com\/blog\/?p=112927"},"modified":"2023-08-15T21:25:57","modified_gmt":"2023-08-15T21:25:57","slug":"ase-a5-exam-latest-2023-2024-actual-exam-questions-and-correct-answers-with-rationalesverified-answers-agrade","status":"publish","type":"post","link":"https:\/\/www.learnexams.com\/blog\/2023\/08\/15\/ase-a5-exam-latest-2023-2024-actual-exam-questions-and-correct-answers-with-rationalesverified-answers-agrade\/","title":{"rendered":"ASE A5 EXAM LATEST 2023-2024 ACTUAL EXAM QUESTIONS AND CORRECT ANSWERS WITH RATIONALES(VERIFIED ANSWERS) |AGRADE"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">ASE A5 EXAM LATEST 2023-2024 ACTUAL<br>EXAM QUESTIONS AND CORRECT ANSWERS<br>(VERIFIED ANSWERS) |AGRADE<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>While aligning a front end, a technician finds the toe out on turns (turning Radius) to<br>be greater than the manufacturer&#8217;s Specs and it has 2.0 degrees difference from the left<br>side to the right side. Which, if any, of the following could be the cause?<br>A. Nothing is wrong; the vehicle has a non symmetrical steering design.<br>B. Bent pitman arm<br>C. bent tie-rod<br>D. Both B and C &#8211; ANSWER- D. either a bent pitman arm or a tie rod could cause the<br>specifications for the toe out on turns to be out of spec. Vehilces with non symmetrical<br>steering systems will have a difference from side to side, but the difference will not<br>exceed the manufacturer&#8217;s specs and it rarely has a greater than 1.5 degrees difference<br>from side to side.<\/li>\n\n\n\n<li>When checking a tire, a tech find it to have too much radial (up and down) runout.<br>Tech A says to rotate the tire and wheel assembly on the mounting studs to correct the<br>problem. Tech B says to rotate the tire on the wheel assembly to attempt to bring the<br>runout within specs. Who is right?<br>A. Tech A Only<br>B. Tech B Only<br>C. Both A and B<br>C. Neither &#8211; ANSWER- B. Rotating the tire on the wheel will compensate for wheel\/tire<br>differential (positioning the highest spot on the tire at the lowest spot on the wheel.)<br>Whereas&#8217;, rotating the wheel assembly on the mounting studs will have no effect on<br>runout.<\/li>\n\n\n\n<li>If you readjust camber on the left front strut, which, if any, of these specs might<br>change<br>A. Right caster<br>B. Left toe and total toe<br>C. SAI<br>D. None of the above. &#8211; ANSWER- B. Readjusting camber will have an affect on the<br>individual toe for the left wheel as well as the total toe. SAI is not adjustable and<br>generally, caster is not adjustable either on a strut suspension.<\/li>\n\n\n\n<li>Too much caster on the left front wheel will cause the <strong><em>__<\/em><\/strong><br>A. vehicle to drift to the left<br>B. Left tire to wear on the outside edge<br>C. vehicle to drift to the right<br>D. left tire to wear on the inside edge. &#8211; ANSWER- C. A vehicle will tend to steer or drift<br>to the side with the least amount of caster. Caster will not cause tire wear, but excessive<br>camber will cause wear to the inside of outside shoulders of a tire.<\/li>\n\n\n\n<li>A driver says that the front end of his car vibrates up and down while traveling at<br>most road speeds. Tech A says that too much runout of the front wheels could be the<br>cause. Tech B says that a static out of balance of the front wheels could be the cause.<br>Who is right?<br>A. Tech A only<br>B. Tech B only<br>C. Both A and B<br>D. Neither A or B &#8211; ANSWER- C. Both Techs are right. Too much runout or static out of<br>balance in the front wheels will cause a vibration<\/li>\n\n\n\n<li>A vehicle has front wheel shimmy at low speed and requires increased steering effort.<br>Tech A says that too much positive camber could be the cause. Tech B says that too<br>much Positive caster could be the cause. Who is right?<br>A Tech A only<br>B. Tech B only<br>C. Both A and B<br>D. Neither A or B &#8211; ANSWER- B. Excessive positive caster will increase steering effort,<br>cause the steering wheel to return too rapidly. cause wander at high speed and shimmy<br>at low speed.<\/li>\n\n\n\n<li>All of these could cause tire wear if not within manufacturer&#8217;s Specs EXCEPT:<br>A. Caster<br>B. Wheel balance<br>C. Toe-In<br>D. Camber &#8211; ANSWER- A. Caster that is out of spec will affect steering and handling<br>characteristics, but will not cause tire wear. Whereas, too much toe in or out would<br>severely wear the tires. Additionally, excessive camber would cause inside or outside<br>shoulder wear on the tire, depending on whether the camber was too negative or<br>positive.<\/li>\n\n\n\n<li>A vehicle with variable assist power steering has a lack of power assist in both<br>directions. Tech A says That the problem is in the electronic control system. Tech B<br>says that there could be a problem in the steering gear or a bad power steering pump.<br>Who is right?<br>A. Tech A only<br>B. Tech B only<br>C. Both A and B<br>D. Neither A or B &#8211; ANSWER- B. Although further diagnosis will be necessary, Tech B is<br>right. Tech A is wrong because, when there is a malfunction in a variable assist power<br>steering system, the system will allow full power steering.<\/li>\n\n\n\n<li>A customer complains that a vehicle wanders on a bumpy road and needs continual<br>driver correction to stay straight. What could be Wrong?<br>A. Excessive negative front caster<br>B. Insufficient front toe<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">C. Rear or front bump steer<br>D. All of the above &#8211; ANSWER- D. Excessive negative caster, insufficient front toe, and<br>front or rear bump steer could cause a vehicle to wander on a bumpy road.<\/p>\n\n\n\n<ol class=\"wp-block-list\" start=\"12\">\n<li>A pressure test is being performed on a car with power steering. The pressure<br>readings taken when the wheels are at the right and left stops are below specs. The<br>tester readings are normal when the tester shutoff valve is closed. tech A says that<br>these readings could be caused by a bad steering gear. tech B says that a bad pump<br>could cause these readings. Who is right?<br>A. Tech A Only<br>B. Tech B Only<br>C. Both A and B<br>D. neither &#8211; ANSWER- A. A bad steering gear would cause the readings to be low when<br>the steering is at the right and left stops, but the readings would be normal with the<br>tester shutoff valve closed.<\/li>\n\n\n\n<li>a vehicle with a manual rack and pinion steering gear has a shimmy. Tech A says<br>that worn rack to frame mounting bushings could be the cause. tech B says that loose<br>inner or outer tie rod ends (sockets) could be the cause. Who is right? &#8211; ANSWER- C.<br>Both Techs are right. Steering play or looseness may occur if the rack to frame<br>mounting bushings are worn, or if the inner or outer tie rod ends are loose. both of these<br>conditions can result in a shimmy.<\/li>\n\n\n\n<li>The ball joints on a Macpherson strut- type suspension are being replaced. Tech A<br>says that coil spring compressor should be installed before separating the control arm<br>and the spindle. Tech B says that the wheel alignment should be checked after the ball<br>joints have been replaced. Who is right?<br>A. tech A Only<br>B. Tech B Only<br>C. Both A and B<br>D. Neither &#8211; ANSWER- B. The wheel alignment should be checked after the ball joint (or<br>any suspension part) is replaced. It is not necessary to install a coil spring compressor<br>prior to separating the control arm and the spindle because the MacPhearson strut<br>assembly contains a spring. However, a spring compressor should be used if the strut is<br>being disassembled.<\/li>\n\n\n\n<li>The rear thrust line reads to the left (drivers side) while the vehicle is at normal ride<br>height. If the wheels were pointing straight ahead, which direction would the vehicle<br>tend to wander<br>A. Veer to the left<br>B. Veer to the right<br>C. Wander to both left and right<br>D. No change occurs &#8211; ANSWER- B. If the thrust line is to the left and the steering<br>wheel is held straight, the vehicle will veer to the right. This happens because the rear<br>wheels will travel towards the left, Which will force the front of the vehicle to the right.<\/li>\n<\/ol>\n","protected":false},"excerpt":{"rendered":"<p>ASE A5 EXAM LATEST 2023-2024 ACTUALEXAM QUESTIONS AND CORRECT ANSWERS(VERIFIED ANSWERS) |AGRADE C. Rear or front bump steerD. All of the above &#8211; ANSWER- D. Excessive negative caster, insufficient front toe, andfront or rear bump steer could cause a vehicle to wander on a bumpy road.<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"default","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[25],"tags":[],"class_list":["post-112927","post","type-post","status-publish","format-standard","hentry","category-exams-certification"],"_links":{"self":[{"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/posts\/112927","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/comments?post=112927"}],"version-history":[{"count":0,"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/posts\/112927\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/media?parent=112927"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/categories?post=112927"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.learnexams.com\/blog\/wp-json\/wp\/v2\/tags?post=112927"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}