CCNA 200-301 DIKTA QUESTIONS EXAM QUESTIONS

PDF Download

CCNA 200-301 DIKTA QUESTIONS EXAM QUESTIONS

Actual Qs and Ans Expert-Verified Explanation

This Exam contains:

-Guarantee passing score -71 Questions and Answers -format set of multiple-choice -Expert-Verified Explanation Question 1: An engineer configures a switch to put interfaces G0/1 and G0/2 into the same Layer 2 EtherChannel. Which of the following terms is used in the configuration commands?

• EtherChannel
• PortChannel
• Ethernet-Channel
• Channel-group

Answer:

Channel-group Question 2: In the LAN for a small office, some user devices connect to the LAN using a cable, while others connect using wireless technology (and no cable). Which of the following is true regarding the use of Ethernet in this LAN?

• Only the devices that use cables are using Ethernet.
• Only the devices that use wireless are using Ethernet.
• Both the devices using cables and those using wireless are using Ethernet.

• None of the devices are using Ethernet.

Answer:

Only the devices that use cables are using Ethernet.Question 3: Which of the following are public IP networks? (Choose three answers.)

• 9.0.0.0
• 172.30.0.0
• 192.168.255.0
• 192.1.168.0
• 1.0.0.0

Answer:

9.0.0.0

192.1.168.0

1.0.0.0

Question 4: The process of TCP on one computer marking a TCP segment as segment 1, and the receiving computer then acknowledging the receipt of TCP segment 1 is an example of what?

• Data encapsulation
• Same-layer interaction
• Adjacent-layer interaction
• OSI model
• All of these answers are correct.

Answer:

Same-layer interaction Question 5: Which of the following protocols are examples of TCP/IP transport layer protocols?

• Ethernet
• HTTP

• IP
• UDP
• SMTP
• TCP

Answer:

UDP and TCP Question 6: Two routers, R1 and R2, connect using an Ethernet over MPLS service. The service provides point-to-point service between these two routers only, as a Layer 2 Ethernet service.Which of the following are the most likely to be true about this WAN? (Choose two answers.)

• R1 will connect to a physical Ethernet link, with the other end of the cable connected to R2.
• R1 will connect to a physical Ethernet link, with the other end of the cable connected to a

device at the WAN service provider point of presence.

• R1 will forward data-link frames to R2 using an HDLC header/trailer.
• R1 will forward data-link frames to R2 using an Ethernet header/trailer.

Answer:

R1 will connect to a physical Ethernet link, with the other end of the cable c nected to a device at the WAN service provider point of presence.R1 will forward data-link frames to R2 using an Ethernet header/trailer.Question 7: Imagine a switch with three configured VLANs. How many IP subnets are required, assuming that all hosts in all VLANs want to use TCP/IP?

• 0
• 1
• 2
• 3
• You cannot tell from the information provided.

Answer:

3

Question 8: A Cisco Catalyst switch has 24 10/100 ports, numbered 0/1 through 0/24. Ten PCs connect to the 10 lowest numbered ports, with those PCs working and sending data over the network. The other ports are not connected to any device. Which of the following answers lists facts displayed by the show interfaces status command?

• Port Ethernet 0/1 is in a connected state.
• Port Fast Ethernet 0/11 is in a connected state.
• Port Fast Ethernet 0/5 is in a connected state.
• Port Ethernet 0/15 is in a notconnected state.

Answer:

Port Fast Ethernet 0/5 is in a connected state.Question 9: Switch SW1 sends a frame to switch SW2 using 802.1Q trunking. Which of the answers describes how SW1 changes or adds to the Ethernet frame before forwarding the frame to SW2?

• Inserts a 4-byte header and does change the MAC addresses
• Inserts a 4-byte header and does not change the MAC addresses
• Encapsulates the original frame behind an entirely new Ethernet header
• None of the other answers are correct

Answer:

Inserts a 4-byte header and does not change the MAC addresses Question 10: Which of the following describes a way to disable IEEE standard autonegotiation on a 10/100 port on a Cisco switch?

• Configure the negotiate disable interface subcommand
• Configure the no negotiate interface subcommand
• Configure the speed 100 interface subcommand
• Configure the duplex half interface subcommand
• Configure the duplex full interface subcommand
• Configure the speed 100 and duplex full interface subcommands