FREE AND STUDY GAMES ABOUT 15-MEN HAIRCUTTING

PDF Download

FREE AND STUDY GAMES ABOUT 15-MEN HAIRCUTTING +

EXAM QUESTIONS

Actual Qs and Ans Expert-Verified Explanation

This Exam contains:

-Guarantee passing score -58 Questions and Answers -format set of multiple-choice -Expert-Verified Explanation Question 1: When ___ and the dryer are used to create wave patterns and direction in the hair, the technique is called blow waving.

Answer:

a comb or brush Question 2: When performing a ___ cut, clipper cutting in the nape should be performed with the clipper tilted on its heel until reaching a point about midway to the ears.

Answer:

medium length Question 3: Shear-over-comb is the most popular technique for eyebrow trimming but a(n) ___ technique can be used as well.

Answer:

outliner-over-comb or small blade guard Question 4: When using the shear-over-comb technique, place the third finger ___.

Answer:

on the finger brace

Question 5: Very short curly hair requires true ___ clipper cutting technique.

Answer:

shorthand Question 6: When tight, curly hair is cut ___, the clipper blade gets clogged and patches and spots may be left.

Answer:

with a short blade Question 7: In a ___ style, when cutting around the ears, remove about 1 inch from the hairline, then use an outliner to trim the sideburns and around the ear areas.

Answer:

semi-short Question 8: Cutting above the fingers is frequently used in men's haircutting to cut and blend layers in the ___ area.

Answer:

All answers are correct. (top, crown, and horseshoe) Question 9: A vertical subsection cut at a ___ projection can be cross-checked by parting off the subsections horizontally at 90 degrees.

Answer:

90-degree

Question 10: Replace dull razors ___.

Answer:

during a cut if necessary

Question 11: Use a changeable-blade straight razor to perform a ___.

Answer:

head shave Question 12: When using the ___ technique, both the fingers and the comb should be in a horizontal position parallel to the floor.

Answer:

fingers-and-shear

Question 13: Reference points are points on the head that mark areas where the surface of the head changes or the behavior of the hair changes

Answer:

as a result of the surface changes Question 14: The ___ is also known as the crest, temporal, horseshoe, or hatband area of the head.

Answer:

parietal ridge

Question 15: Concave profiles require ___.

Answer:

a close hair arrangement over the forehead

Question 16: Use maximum tension on ___.

Answer:

straight hair to create precise lines.

?

Question 17: Size 0000 detachable blades are ___.

Answer:

closest to shaving

Question 18: Finger-styling produces a ___ look than brush styling.

Answer:

more textured Question 19: Flat tops are traditionally slightly longer in the ___ sections and flat across the top of the head form

Answer:

front and crest

Question 20: A brush cut is also called a ___.

Answer:

crew cut Question 21: For a ___ style, clipper cutting is performed up to the occipital areas and on the sides to the bottom of the crest.

Answer:

medium-length

Question 22: Clippers are used to facilitate ___ on a fade cut.

Answer:

blending

Question 23: When using the arching technique, the barber ___.

Answer:

uses the center of the shear blade Question 24: In the shear-over-comb technique, align the still blade of the shears with the comb ___.

Answer:

below the still blade Question 25: The razor-over-comb technique is often used to taper nape areas or to ___.

Answer:

soften weight lines Question 26: The Quo Vadis is a popular very short haircut style that is suitable for ___ hair.

Answer:

very curly

Question 27: A straight profile tends to be the most balanced and

Answer:

can usually wear any hairstyle successfully