FREE AND STUDY GAMES ABOUT SHEET METAL EXAM

PDF Download

FREE AND STUDY GAMES ABOUT SHEET METAL EXAM

QUESTIONS

Actual Qs and Ans Expert-Verified Explanation

This Exam contains:

-Guarantee passing score -69 Questions and Answers -format set of multiple-choice -Expert-Verified Explanation

Question 1: The general rule for finding the proper rivet diameter is

Answer:

three times the thickness of the thickest sheet

Question 2: What is the most common method of cementing transparent plastics?

Answer:

soak method Question 3: Composite fabric material is considered to be the strongest in what direction?

Answer:

warp Question 4: Heat-treated rivets in the D and DD series that are not driven within the prescribed time after heat treatment or removal from refrigeration

Answer:

must be heat treated before use

Question 5: The monocoque fuselage relies largely on the strength of

Answer:

skin or covering Question 6: The classification for high tensile strength fiberglass used in aircraft structures is

Answer:

S-glass

Question 7: Which rivet is used for riveting magnesium alloy structures?

Answer:

5056 aluminum

Question 8: The markings on the head of a Dzus fastener identify the

Answer:

body diameter, type of head, and length of fastener

Question 9: You can distinguish between aluminum and aluminum alloy by

Answer:

testing with a 10 percent solution of caustic soda Question 10: Fiberglass laminate damage not exceeding the first layer or ply can be repaired by

Answer:

filling with a putty consisting of a compatible resin and clean, short glass fibers.Question 11: On a sheet metal fitting layout with a single bend, allow for stretching by

Answer:

subtracting the setback from both legs Question 12: The identifying marks on the heads of aluminum alloy rivets indicate the

Answer:

specific alloy used in the manufacture of the rivets

Question 13: The most important factors needed to make a flat pattern layout are

Answer:

radius, thickness, and degree of bend

Question 14: A well-designed rivet joint will subject the rivets to

Answer:

Shear loads

Question 15: (Refer to Figure 7.) What is dimension F?

Setback at D = .095 Setback at E = .068 Bend allowance at D = .150 Bend allowance at E = .112

Answer:

5.936 Question 16: The length of a rivet to be used to join a sheet of .032-inch and .064-inch aluminum alloy should be equal to

Answer:

one and one-half times the rivet diameter plus .096 inch Question 17: Which of the following need not be considered when determining minimum rivet spacing?

Answer:

Rivet length

Question 18: Which is an identifying characteristic of acrylic plastics?

Answer:

Zinc chloride will have no effect

Question 19: The purpose of a joggle is to

Answer:

allow clearance for a sheet on an extrusion

Question 20: When repairing puncture-type damage to a metal-faced laminated honeycomb panel, the edges of the doubler should be tapered to

Answer:

100 times the thickness of the metal Question 21: If it is necessary to compute a bend allowance problem and bend allowance tables are not available, the neutral axis of the bend can be

Answer:

found by adding approximately one-half of the stock thickness to the bend radius.

Question 22: What is a rivet's grip length?

Answer:

the total thickness of the material held together by the rivet Question 23: How many MS20470 AD-4-6 rivets will be required to attach a 10 x 5 inch plate, using a single row of rivets, minimum edge distance, and 4D spacing?

Answer:

56 Question 24: Under certain conditions, type A rivets are not used because of their

Answer:

low strength characteristics Question 25: If a new safety belt is to be installed in an aircraft, the belt must conform to the strength requirements in which document?

Answer:

TSO C22

Question 26: A DD rivet is heat treated before use to

Answer:

soften to facilitate riveting

Question 27: The shop head of a rivet should be

Answer:

one and one-half times the diameter of the rivet shank